What Side of House Does Sattelite Dish Best

February 20, 2022 Post a Comment

Download Article

Rather if you lot have Dish, AT&T, or cablevision and y'all are planning on getting satellite service for your home, you don't need to telephone call a professional person installer. Even if y'all don't take much construction feel, yous tin can fix up a satellite dish. Once you lot find an exact spot for your dish, mount it in place. Receive a satellite signal by pointing the dish upwardly to the sky. With proper wiring, you can then transfer the point to a receiver and your TV.

i
Select a flat spot on or effectually your home. Find a level place that is accessible if y'all need to make clean off or suit the satellite dish later. If you accept infinite, the safest place for a satellite dish is on the ground. It volition have plenty of room to point north or south, depending on where you alive. Besides, proceed the dish away from falling snowfall or ice, such every bit from your roof or nearby trees.^[one]
- Remember where the TVs are in your dwelling house. Try to find a spot close to them to make the wiring process easier.
- If you mount the dish on the footing, you will need to dig a trench to run its cables to your home safely.
2
Check for any obstructions blocking the dish'south view of the sky. Stand where y'all plan on installing the dish. Look upwardly to the sky. If yous see buildings, trees, or even clotheslines in the way, then find some other spot. These obstacles stop the dish from receiving a clear signal, affecting your picture quality.^[ii]
- One of the best means to gear up a dish is past anchoring a metal pole in the basis with concrete, then mounting the dish on top of information technology. The rod gives the dish more height without it needing to be on the roof.
- Satellite dish installers almost automatically go for the roof to guarantee the satellite isn't obstructed. Y'all may need to do this, also, if you can't detect an exact spot elsewhere.
- If yous're in the northern hemisphere, the dish needs to point south to receive a signal. If y'all're in the southern hemisphere, it needs to point north, so keep that in mind when looking for obstacles.
Advertisement
3
Hold the dish's mountain to your home and mark the screw positions. The dish'southward back up is an L-shaped rod with a base plate that fastens to your home. Position the base of operations plate flat against the wall or roof in the location you chose. Look for a series of holes on the plate for bolts. Then, use a permanent marker to note the position of these holes on the roof.^[iii]
- If you're attaching the satellite to the side of your home, brand sure the holes align with a wall stud or another sturdy structure. Don't try to anchor it to siding since it won't hold.
4
Calculate the size of the pilot holes needed to secure the mountain. The holes' verbal size and depth depend on the dish you're installing, so reference the components that came with the satellite. Generally, you will need to make a series of iv holes about ⁱ⁄₂ in (1.3 cm) in bore. Judge the holes needed to exist about {convert|two+i/ii|in|cm|abbr=on}} deep, although this will besides vary a little from installation to installation.^[iv]
- Cheque the metal fixings that came with your satellite for a number engraved on them. That number volition tell you how wide the holes need to be.
- To find the depth the holes demand to be on your detail installation, add nearly ⁱⁱ⁄_x in (0.51 cm) to the length of the metallic fixings meant to plug into the holes.
v
Create the airplane pilot holes using a drill fleck the same size as the mounting bolts. Utilize a masonry drill flake to suspension through rock and other rigid surfaces without damaging your drill. The flake needs to create holes that are the perfect size for the bolts. Drill into the spots y'all marked earlier one time you are ready. Make sure the holes y'all create are directly, and so the mounting bolts fit properly.^[5]
- If the holes are too big, the bolts will fall out. If they are too small, the bolts won't fit.
- Erring on the side of caution is better when drilling. Y'all can always widen a small hole.
6
Place the mount's metallic plugs into the holes yous drilled. Your dish will come up with a fix of metal plugs that serve as wall anchors. One cease of each plug will take a bolt hole in it. Flip the plugs, so the openings confront toward you rather than the wall. You need those openings to secure the mountain.^[six]
- The opposite ends of each plug will look like a split tail. When y'all commodities the wall mount in place, the tails open, making the plugs harder to remove.
seven
Secure the plugs into the wall with a hammer and chisel. Place the tip of a chisel against i of the bolts. Give the chisel'due south handle a couple of practiced whacks to push the bolt into the wall. Go along hammering until the bolt is flush with the wall. And so, repeat this with the remaining bolts.
- Make sure the bolts are level with the wall, or else the dish'southward mount won't anchor properly.
viii
Place the metal plugs and hammer them into the wall. Your dish will come up with a fix of plugs that serve as wall anchors. Position them, so their open up terminate faces out from the wall. That opening is for bolting the wall mount in place. After pushing the plugs into the holes, tap them in with a hammer and chisel.^[7]
- Brand sure the plugins are firmly positioned inside the wall. They are what anchors the mount to the wall or ceiling. If they are loose, your dish could end up crashing to the ground!
9
Bolt the mount onto the plugs in the wall. Position the mountain back on the wall, lining up the plate's holes with the pilot holes yous drilled. Observe the bolts that came with your dish, usually ¹⁄₂ in (1.iii cm) lag bolts. Spike the bolts by using a cordless screwdriver. Make sure the mount feels secure in the wall before you motion on.^[eight]
- If the mountain wobbles when you touch information technology, endeavour tightening the bolts a little more. If y'all're sure they are in correctly, have them out and recheck the plugs.
10
Cap each commodities with a metal washer and locking nut. These components prevent the bolts from coming back out of the wall. Slide the washers on first, which are flat metal disks that assist the nuts work properly. Then, add the nuts and turn them clockwise with a wrench until they feel tight and no longer motility.
- Exist conscientious not to overtighten the nuts. Stop twisting them when they get hard to motion. As long as they are non loose, the mount will also stay in identify.
Ad

i
Attach the antenna bracket to the low dissonance block (LNB) arm. Your dish will most likely come with a apartment metallic plate to connect the satellite dish to the L-shaped LNB arm and other components. Position the plate, so the prongs are on the left and right, facing you lot. Concur the LNB arm betwixt the prongs with the tail end extending out past the plate's contrary side. Place some ³⁄_four in (1.9 cm) lag bolts through the arm and into the plate, tightening them clockwise with a wrench.^[9]
- Remember to put a metal washer and locking nut on the ends of the bolts to ensure they can't come loose.
- The exact installation process, including the bolts' size, may vary a little depending on the dish you have. Refer to the owner's manual for more specific instructions.
2
Clip the antenna adjustment panel over the plate's prongs. The panel will look like a square box with one end open up. The panel's sides fit over the plate's prongs and attach with more ³⁄₄ in (ane.ix cm) lag bolts. Add a washer and nut on the finish of each bolt after tightening them.^[10]
- The aligning panel has a curved slot on information technology. This slot is what you use to point the satellite up or downward.
3
Fit the U-shaped rod within the adjustment panel. Your dish will have a aptitude metal rod that fits into i of the slots on the adjustment panel. Skid the rod within, sliding its prongs through the holes. Ensure the prongs point toward y'all rather than the tail finish of the LNB rod y'all connected before. Fit a small clench over it, followed by a washer and nut on each prong.^[xi]
- The clamp is petty more than than a flat piece of metal meant to agree the U-shaped rod in place.
- The adjustment panel has three dissimilar slots. Use the slots to reposition the satellite dish. In most cases, the center slot is all-time for setting the dish at the proper angle.
4
Bolt the antenna subclass to the back of the satellite dish. You take a couple more bolts to add to finish the bulk of the assembly, and this is one of the easiest parts to finish. Line up the holes on the plate with the holes on the back of the dish. Stick the longest bolts y'all take, usually 2 to three in (5.one to seven.half-dozen cm) in length, through the front of the dish. So, place a washer and nut on the finish of each bolt, tightening it with your wrench.^[12]
- Make certain all of the components stay bolted together. If they feel shaky, carefully separate them and tighten the bolts.
five
Install the LNB on the end of the LNB arm. One last component, the LNB, controls the dish's functionality. Outset, slide the handle of the LNB onto the open finish of the arm. Secure information technology with nuts and bolts, then accept the LNB out of the box. It looks near like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place.^[thirteen]
- Some more robust satellites take up to 3 LNBs designed to feed a stronger satellite point into your home.
- You may need to loosen the LNB later to readjust it and improve the betoken quality.
6
Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open up stop of the support. If everything is attached correctly, it volition fit inside or backside the adjustment panel. Y'all can then add the i or 2 remaining bolts to spike these pieces together. If the dish looks good, then you're ready to position information technology to communicate with a satellite.^[14]
- These parts can attach in a variety of different ways depending on what satellite you take, and then be certain to refer to the owner's manual.
- If the mountain is meant to attach to the back of the panel, your satellite will likewise come up with a pair of clips. Position them behind the back up, then add the screws through them to bind the parts together.
Advertisement

1
Select a satellite you wish to connect to. Selection a satellite that is in range of your item dish. There are numerous satellites out there, just dishes cannot go signals from all of them. If y'all bought your dish from a TV service, for instance, you might take a difficult fourth dimension connecting to their competitor's satellites. Search for bachelor satellites at https://www.lyngsat.com/.^[15]
- To differentiate betwixt satellites, look at the names listed along with the coordinates. Tracking sites list the names, which usually include the owning company or the service they provide.
- If you lot bought a satellite service, it is possible to receive satellite signals outside that service. Since you lot ordinarily need to replace several parts, information technology'south easier to get a new satellite instead.
- Try to pick a satellite shut to your area. If y'all subscribe to a particular Television receiver service, you lot will demand to use the company's satellites. The biggest providers have multiple satellites.
2
Observe the satellite'south location before positioning the dish. Yous're going to demand to point the dish in the correct direction, and so bending it upwardly at the sky. This isn't easy to practise if y'all don't know the satellite's positioning. Fortunately, satellites don't movement much, so you tin can use a positioning database to accommodate your dish. Apply a site like https://www.dishpointer.com/.^[16]
- Blazon in your address and choose a satellite you wish to connect to. The site will give y'all the precise positioning needed for your dish to receive the signal.
- You won't be able to receive a signal from a distant satellite. Don't wait to reach a Chinese satellite if yous're in North America, for example.
3
Utilise the azimuth number to rotate the satellite. Have a compass handy and locate true north beginning. Then, look at the azimuth number and detect where that is on the compass. North is considered 0 degrees, e is ninety degrees, due south is 180 degrees, and west is 270 degrees. Rotate the satellite dish horizontally until information technology points in the correct management.^[17]
- For case, if you lot demand to point the dish to 225 degrees, find north commencement. Then, turn the satellite southwest from there.
4
Move the dish vertically to suit its elevation. Once y'all know the summit needed to reach the satellite, get behind the dish. Examine the finish of the mount where it connects to the dish. You volition see a bolt inside a slot labeled by degrees, usually 10 to 60. Loosen the bolt by twisting information technology counterclockwise, then reposition the dish to the proper top.^[eighteen]
- Adjusting the elevation is unremarkably pretty easy because of the labeled slot. Moving the commodities along the slot raises or lowers the dish.
- For instance, if the dish requires a 53-degree superlative, information technology will point up into the sky almost as much as it perchance can. Slide the loosened bolt back toward the sixty-degree marking.
v
Adjust the dish's polarization until you lot become a clear signal. The concluding part that needs to be adjusted is LNB, responsible for receiving and sending the signal into your abode. It is usually an arm on the front that points toward the dish. Examination out the betoken quality past hooking the dish up to the receiver and a TV, so loosen the connecting nut on the arm by turning information technology counterclockwise with a wrench. Gradually move the arm about ¹⁄₂ in (1.three cm) at a time until the signal quality is perfect.^[xix]
- This function is easier if you can set up a TV close to the dish. If the TV is far away, take someone else stand near information technology and give y'all feedback.
- Yous may demand to wait to conform the LNB until yous're washed with the wiring. Accept intendance of it before then, if you're able, and then you don't have to proceed climbing on the roof to brand adjustments.
- The LNB can sometimes exist controlled past turning a mount part on the dorsum of the dish left or right.
Ad

i
Drill a ¹⁄₂ in (1.3 cm) hole in the roof if you need one. Cheque your habitation first for a previously-used cablevision opening. The dish'due south cable needs its own little space to enter your habitation and hook up to your Telly. Unless your dwelling house is in the process of beingness built, drilling a single pigsty is the easiest way to do this. Position your Idiot box and the satellite receiver nearby to prepare for the connection.^[20]
- If y'all're installing the satellite on the ground, dig a trench to bury the cable, so it doesn't go damaged. It needs to be below the frost line, the everyman point that freezes in winter, which is about 3 in (7.6 cm) deep.
2
Run a coaxial cablevision from the LNB to the receiver. Get a basic RG6 coaxial cable and look for a slot on the LNB. Plug it in, and so plug the opposite finish into the "Sabbatum in" port on your receiver. Brand sure the receiver is positioned shut to the satellite to ensure the cable can accomplish it.^[21]
- Yous can buy a cable online, from hardware stores, and as well from electronics suppliers. Television receiver service providers will also give you one when you purchase a satellite from them.
- The coaxial cable sometimes connects to the back of the satellite. Commonly, though, information technology plugs directly into the LNB.
3
Connect an HDMI cable to the receiver and your TV. Plug one finish of the HDMI cable into the receiver's back, then stretch it to the Boob tube. Near modern TVs accept a couple of HDMI slots, so choose whichever one you adopt. Once the cord is in place, your Television set will be able to receive the satellite signal. Plow on the TV to run into if information technology works.^[22]
- Some satellites and receivers don't connect this style. The receiver may plug directly into the Television set instead.
- Consult a wiring guide for specific instructions on how to connect the satellite, receiver, and your Boob tube. If yous bought the satellite from a Boob tube service provider, they would also provide a wiring guide.
4
Turn on the TV to test the signal. Press the satellite button if your remote has one or navigate to the settings card. You should exist able to get a film right abroad. If the indicate quality is poor, make sure you positioned the satellite dish correctly. Adapt it to become the clearest possible signal!^[23]
- You can check the settings card to become an thought of where the satellite dish is.Please note the azimuth, top, and LNB numbers and compare them to the satellite'south location.
Advertisement

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Enquire Television service providers for an install. Many of them offering free installations as long as you lot purchase a subscription for their service.
Observe spots to hide loose cables in your home. If the satellite dish's cablevision is exposed, put piece of furniture and other decorations in forepart of information technology.
Every satellite receiver needs a separate coaxial cablevision. You can't divide the cablevision, and then you will demand to find ways to route the cables all the mode to the extra TVs you programme on setting up.
If you're running a coaxial cablevision outdoors along the ground, consider installing a grounding block and wire to protect the cable from static.